無塵車間對溫濕度的控制決取于其生產工藝。在滿意加工工藝的條件下，還應該考慮到人的舒適感。因為人出汗以后，對產品將有污染，特別是怕鈉的半導體車間，這種車間不宜超越25度。濕度過高產生的問題更多。相對濕度超越55%時，冷卻水管壁上會結露，假如發生在精密裝置或電路中，就會引起各種事故。相對濕度在50%時易生銹。下面，就隨著背光模組無塵車間廠家一起來看看常見無塵車間對溫濕度有要求的工藝吧！

　　示例一：

　　在精密機械加工和計量等場合，為了防止因熱膨脹而引起的差錯，有必要使工件保持必定的溫度。工件溫度的答應波動起伏應根據加工精度決議。例如，在恒溫室里對一根長500mm的標準尺刻線，工藝答應線間公役為2um，其中lum為尺溫改變所引起的形變差錯，另1um為加工與量測差錯。1um折合尺溫改變量＝0.20C[a為尺線膨脹系數，取10／um／(m?K)；l為尺長，m]，故工件溫度改變需在：以內。但由于工件測量儀器等都有必定的熱惰性，空氣溫度的波動傳人工件后，就要衰減。在設計恒溫體系時，一般總是以恒定環境空氣溫度為根據，故相應的環境溫度精度可比工件答應的溫度精度低一些。因此，在確定恒溫室參數和選擇自動控制時，有必要考慮工件恒溫恒濕車間、圍護結構、空氣處理設備和自控體系之間的動態特性。

　　示例二：

　　在電子行業制作車間是樶重要產生靜電的當地，通常靜電會對產品形成短路甚至會形成職工導電暈倒事故，所以電子行業的無塵車間相對濕度不該低于30%，這樣即可以削減靜電的產生，通常建議無塵車間的防靜電區域相對濕度不低于50%。過于干燥的空氣中易粉塵飛揚，電子廠無塵車間無特殊要求的情況下，溫度控制在22℃左右，相對濕度控制在55～60%RH之間，在這種環境下，人們感覺舒適，靜電也消失了。

標簽：背光模組無塵車間